Epson ActionPrinter 4500 User Manual Download Page 250

Page: 250 / 317

Initialization

There are two ways that the printer can be initialized (returned to the

default settings) through the hardware and one way through the
software. These are described in the following table:

The software sends the ESC @ (initialize

Default Settings

The table below shows the default conditions that become valid when

the printer is initialized.

Item

Reset to:

Top of form positron

Left and right margins

Current paper position

Cancelled

Line spacing

1/6-inch line spacing

Vertical tab position

Horizontal tab positions

VFU channel

Cleared

Every eight characters

Channel 0

Font selection

Hardware: The current DIP switch setting

Software: The current SelecType setting

Condensed mode

Hardware: The current DIP switch setting

Software: The current SelecType setting

Character spacing

The current DIP switch setting

Justification

Left justification

Special printing effects

Cancelled (except condensed printing)

Graphic mode assignment

ESCK = ESC*0,ESCL = ESC*1,
ESCY = ESC*2,ESCZ = ESC*3

8-14

Technical Specifications

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Epson ActionPrinter 4500, User Manual, Page: 250 / 317

Search results

Summary of Contents for ActionPrinter 4500

Reviews: