Epson ActionPrinter 4500 Page 226 User Manual Download | Manualshive

Page: 226 / 317

background image

Options

Problem

Using the cut sheet

feeder, the paper does

not feed properly.

The

LOAD/EJECT

button is pressed, but
the platen does not
move and the paper
does not feed.

After a print

command is sent from
the computer, the
platen does not move
and the paper does not
feed.

Solution

You may be pressing the

LOAD/EJECT

button while the printer is on line. Always

put the printer off line before feeding the
paper. Paper feeds automatically when the
cut sheet feeder receives a print command

from the computer (only while the printer
is on line).

The printer may be off line. Press the

ON

LINE

button to put the printer on line.

The cut sheet feeder mode may be off. Set
DIP switch 1-8 to on. If your program

allows you to use control codes, use ESC
EM 4 to set the cut sheet feeder mode. The
printer must be ready with no paper out
condition to receive this command. Send

the command with continuous paper
loaded and with the paper select lever in

the continuous paper position.

7-24

Troubleshooting

«
...
224
225
226
227
228
...
»

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments

Related manuals for ActionPrinter 4500

Brand: Unitech Pages: 18

Brand: Unitech Pages: 26

Brand: Panduit Pages: 6

Brand: Xante Pages: 25

Brand: Radio Shack Pages: 57

Brand: Partner Pages: 34

Brand: Me3D Pages: 14

Brand: Anyload Pages: 12

DocuColor 45087638

Brand: Xerox Pages: 28

Brand: Ultimaker Pages: 4

PIXMA MG2220 Series

Brand: Canon Pages: 4

Brand: Canon Pages: 16

Brand: Canon Pages: 28

Brand: Canon Pages: 20

PIXMA E3300 Series

Brand: Canon Pages: 64

Brand: Canon Pages: 20

Brand: Canon Pages: 46

Brand: Canon Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands