manualshive.com logo in svg

Epson ActionPrinter 4500, User Manual

The Epson ActionPrinter 4500 is a reliable and high-performance printer designed for efficient and professional printing needs. As a user-friendly device, it comes with a comprehensive User Manual, which can be easily downloaded for free from manualshive.com, providing step-by-step guidance for optimal usage and maintenance.

Share
Download
background image

Printing

Problem

Solution

The printer does not

print.

The 

ON LINE 

light is on

but nothing is printed.

The ON

off.

LINE 

light is

The 

PAPER OUT 

light is

on.

The software may not be installed properly
for your printer. Check the printer settings

and make the necessary changes.

The interface cable may be loose. Check
both ends of the cable between the printer

and the computer. Secure the connector
using the wire retaining clips.

You may not be using the correct interface

cable. Make sure your interface cable meets
the printer and the computer specifications.

The printer may be off line and cannot
receive data. Press the 

ON LINE 

button. The

ON LINE 

light should go on. See Chapter 3.

The printer may be out of paper. Load

more paper into the printer. See Chapter 2.

The paper may be set too far to the right,
so that the paper detector cannot sense it.
Move the paper a little to the left. The

PAPER OUT 

light should go off.

Troubleshooting 7-5

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments

Related manuals for ActionPrinter 4500

Canon imageCLASS Mf6160dw Getting Started Manual preview
imageCLASS Mf6160dw
Brand: Canon Pages: 64
Canon imageCLASS MF6500 Series Advanced Manual preview
imageCLASS MF6500 Series
Brand: Canon Pages: 132
Canon imageCLASS MF5550 Software Manual preview
imageCLASS MF5550
Brand: Canon Pages: 120
Canon imageCLASS MF5630 User Manual preview
imageCLASS MF5630
Brand: Canon Pages: 85
Canon imageCLASS MF5550 Basic Manual preview
imageCLASS MF5550
Brand: Canon Pages: 136
Canon IMAGECLASS MF7400 Starter Manual preview
IMAGECLASS MF7400
Brand: Canon Pages: 40
Canon imageCLASS MF5850dn Settings Manual preview
imageCLASS MF5850dn
Brand: Canon Pages: 34
Canon imageCLASS MF6500 Series Starter Manual preview
imageCLASS MF6500 Series
Brand: Canon Pages: 16
Canon imageCLASS MF6540 Software Manual preview
imageCLASS MF6540
Brand: Canon Pages: 82
Canon imageCLASS MF5550 Facsimile Manual preview
imageCLASS MF5550
Brand: Canon Pages: 99
Canon imageCLASS MF5630 Quick Reference Manual preview
imageCLASS MF5630
Brand: Canon Pages: 24
Canon imageCLASS MF5770 Setup Sheet preview
imageCLASS MF5770
Brand: Canon Pages: 2
Canon imagePRESS C7000VP Series Customer Expectation Document preview
imagePRESS C7000VP Series
Brand: Canon Pages: 48
Canon imageClass MF5650 Parts Catalog preview
imageClass MF5650
Brand: Canon Pages: 40
Canon imageCLASS MF5770 User Manual preview
imageCLASS MF5770
Brand: Canon Pages: 8
Canon imageCLASS MF4880dw Starter Manual preview
imageCLASS MF4880dw
Brand: Canon Pages: 36
Canon imageCLASS MF4890dw Basic Operation Manual preview
imageCLASS MF4890dw
Brand: Canon Pages: 116
Canon ImageCLASS MF4690 Reference Manual preview
ImageCLASS MF4690
Brand: Canon Pages: 387

Brands by name

Popular brands

Load more brands