manualshive.com logo in svg

Epson ActionPrinter 4500, User Manual

The Epson ActionPrinter 4500 is a reliable and high-performance printer designed for efficient and professional printing needs. As a user-friendly device, it comes with a comprehensive User Manual, which can be easily downloaded for free from manualshive.com, providing step-by-step guidance for optimal usage and maintenance.

Share
Download
background image

Problems and Solutions

This chapter discusses problems you may encounter while operating
your printer and their likely solutions. If you are having difficulty

achieving the desired printing result, first locate the problem in the table
below and then see the appropriate page for the solution.

Power supply

l

Power is not being supplied.

Printing

l

The printer does not print.

l

The print is faint or uneven.

l

Dots are missing in the printed characters or
graphics.

l

Printed characters are not what you expected.

l

The print position is not what you expected.

See 7-4

See 7-5

See 7-6

See 7-7

See 7-8

See 7-11

Paper handling

l

Single sheets do not feed properly.

l

Continuous paper does not feed properly.

l

Switching between single sheets and continuous
paper cannot be performed properly.

l

The short tear-off function does not operate
properly.

See 7-14

See 7-17

See 7-21

See 7-23

7-2

Troubleshooting

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments

Related manuals for ActionPrinter 4500

Xerox 3270 Programmer'S Manual preview
3270
Brand: Xerox Pages: 34
Xerox B210 Manual preview
B210
Brand: Xerox Pages: 73
Xerox B210 Installation Manual preview
B210
Brand: Xerox Pages: 2
Unisys 115 Operation/Reference Manual preview
115
Brand: Unisys Pages: 255
Xerox B210 User Manual preview
B210
Brand: Xerox Pages: 199
Oki B2200 Maintenance Manual preview
B2200
Brand: Oki Pages: 100
Oki B2200 Quick Setup Manual preview
B2200
Brand: Oki Pages: 2
Xerox B235 User Manual preview
B235
Brand: Xerox Pages: 316
Xerox B215 Get Started preview
B215
Brand: Xerox Pages: 74
Xerox B215 User Manual preview
B215
Brand: Xerox Pages: 306
Xerox B215 Quick Use Manual preview
B215
Brand: Xerox Pages: 16
Xerox B210 Quick Start Manual preview
B210
Brand: Xerox Pages: 4
Oki B2200 Guide Utilisateur preview
B2200
Brand: Oki Pages: 38
Oki B2200 Guía Del Usuario preview
B2200
Brand: Oki Pages: 38
Oki B2200 User Manual preview
B2200
Brand: Oki Pages: 36
Oki B2200 Safety & Warranty preview
B2200
Brand: Oki Pages: 36
Samsung CJX-1050W Quick Install Manual preview
CJX-1050W
Brand: Samsung Pages: 2
TallyGenicom 6300 Series Maintenance Manual preview
6300 Series
Brand: TallyGenicom Pages: 175

Brands by name

Popular brands

Load more brands