manualshive.com logo in svg

Epson ActionPrinter 4500, User Manual, Page: 187 / 317

Share
Download
Epson ActionPrinter 4500 User Manual Download Page 187

The Interface Boards

2. Reattach the board cover.

CAUTION: When 

an optional interface board is installed, be

sure to disconnect the printer cable from the printer’s built-in

#8143 New Serial Interface

If you are using an optional interface, it may be necessary for you to
alter the communication protocol of the printer or the computer so that

they can communicate properly. In most cases, you should use the
information in your optional interface manual or your computer’s
manual to match the computer with the interface.

If you are using the #8143 optional interface board, make sure that you
read through the section below on baud rate selection. You may also
want to see the following sections on handshaking timing and error
handling for interface information specific to your printer.

For all other data transfer conventions, such as word structure or

communications protocol, use the information in the manual supplied

with your #8143 optional interface.

Using 

the 

Printer Options

5-49

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments