Epson ActionPrinter 4500 Page 178 User Manual Download | Manualshive

Page: 178 / 317

background image

The Interface Boards

A number of optional interfaces are available in case your computer is

either not provided with a parallel interface or you wish to increase the
memory capacity of your printer’s buffer.

Choosing an Interface

Optional interfaces can be divided into three main categories which are
described briefly below.

IEEE-488 interfaces offer standardized connections, trouble-free
operation, and the ability to connect computers, printers, and other

devices on the same line so that they may share data freely.

The buffered parallel interfaces also offer trouble-free operation and
standardized connections. They provide the printer with more

memory to free the computer for other tasks when printing large
amounts of text or graphics. You can increase the printer’s data
buffering capacity by an additional 32 KB (about 10 pages).

Serial interfaces are required if your computer is not equipped with
a parallel interface or if you need an interface that conforms to the
Current Loop standard instead of RS-232C. These interfaces also
provide some combination of the following features: X-ON/X-OFF
data communication protocol, loopback self test modes, and data
buffers that increase the printer’s data buffering capacity.

5-40

Using the Printer Options

«
...
176
177
178
179
180
...
»

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments

Related manuals for ActionPrinter 4500

Brand: Pandigital Pages: 2

Brand: Xerox Pages: 13

Brand: Xerox Pages: 16

Brand: Lanier Pages: 298

6130N - Phaser Color Laser Printer

Brand: Xerox Pages: 2

6130N - Phaser Color Laser Printer

Brand: Xerox Pages: 2

Brand: Lexmark Pages: 59

Brand: Chamiin I&C Pages: 18

Brand: Oki Pages: 20

DRYPRO Model 793

Brand: Konica Minolta Pages: 156

Brand: Oki Pages: 198

Brand: SEWOO Pages: 13

Brand: Ricoh Pages: 74

Brand: Nehoc Pages: 9

Brand: Mayku Pages: 2

Brand: Flashforge Pages: 63

Brand: Lexmark Pages: 2

Brand: Savin Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands