manualshive.com logo in svg

Epson ActionPC 5000, User Manual

Share
Download
Epson ActionPC 5000 User Manual Download Page 117

Most problems you encounter while operating your printer
have simple solutions. Read through the appropriate section to
find your problems; then follow the recommended steps. If
you cannot solve the problem, contact your dealer or a
qualified service person for assistance.

Power Supply

The printer does not work and the 

OPERATE 

light does not come

on.

Check that the power cord is plugged into the electrical outlet
properly.

If the electrical outlet is controlled by an outside switch or
automatic timer, use a different outlet.

Plug another electrical device into the outlet to determine
whether the outlet is operating properly.

The 

OPERATE 

light comes on briefly and then goes off. The light

stays off even when the power is switched on again.

Check that the printer’s voltage rating matches the voltage of
your electrical outlet. If the voltages do not match, unplug the
printer and contact your dealer immediately. Do not reconnect

the power cord to an electrical outlet.

Printing

The printer does not print and the 

PAUSE 

light is on.

Press the 

PAUSE button.

6-2 Troubleshooting

Summary of Contents for ActionPC 5000

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands