background image

38

Using the Control Panel

L

Changing the Printer’s Default Settings

While you can often change the printer’s settings through your software 
or printer driver, you may sometimes need to change one or more of the 
printer’s default settings. There are two ways to do this:

Using the EPSON Remote Configuration Manager on the printer 
software CD-ROM. (See page 15.)

From the printer’s control panel using the default-setting mode.

For instructions on using the Remote Configuration Manager, see the 
PDF manual on the CD-ROM. To use the control panel, see below. For 
detailed information about default settings, see the 

Reference Guide

. The 

following table shows the options available for each printer setting. 

Setting

Options (default in bold)

Page length for front 
tractor

Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5, 

11

, 70/6, 12, 

14, 17

Page length for rear 
tractor

Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5, 

11

, 70/6, 12, 

14, 17

Skip over perforation

Off

, On

Auto tear-off

Off

, On

Auto line feed

Off

, On

Print direction

Bi-D

, Uni-D

Software

ESC/P

, IBM PPDS

0 slash

0

,  

I/F (interface) mode

Auto

, Parallel, USB, Option

Auto I/F wait time

10 seconds

, 30 seconds

Parallel I/F bidirectional 
mode

Off, 

On

Packet mode

Auto

,

 

Off

Character table

Italic, 

PC 437

, PC 850, PC 860, PC 863, PC 865, PC 861, 

BRASCII, Abicomp, Roman 8, ISO Latin 1, PC 858, 
ISO 8859-15

International character 
set for italic table 

Italic U.S.A.

, Italic France, Italic Germany, Italic U.K., 

Italic Denmark 1, Italic Sweden, Italic Italy, Italic Spain 1

Manual feed wait time

1 second, 

1.5 seconds

, 2 seconds, 3 seconds

Buzzer

Off, 

On

Summary of Contents for 2190 - FX B/W Dot-matrix Printer

















































Reviews: