Epson 11880 - Stylus Pro Color Inkjet Printer User Manual Download Page 7 | Manualshive

Page: 7 / 182

background image

Safety Instructions

7

User’s Guide

❏

Do not use a damaged or frayed power cord.

❏

If you use an extension cord with this
product, make sure the total ampere rating of
the devices plugged into the extension cord
does not exceed the cord’s ampere rating.
Also, make sure the total ampere rating of all
devices plugged into the wall outlet does not
exceed the wall outlet’s ampere rating.

❏

Do not attempt to service this product
yourself.

❏

Unplug this product and refer servicing to
qualified service personnel under the
following conditions:

The power cord or plug is damaged; liquid
has entered the product; the product has been
dropped or the cabinet damaged; the product
does not operate normally or exhibits a
distinct change in performance.

❏

If you plan to use the printer in Germany,
observe the following:

To provide adequate short-circuit protection
and over-current protection for this printer,
the building installation must be protected by
a 10 or 16 amp circuit breaker.

❏

If damage occurs to the plug, replace the cord
set or consult a qualified electrician. If there
are fuses in the plug, make sure you replace
them with fuses of the correct size and rating.

When using this product

❏

Do not put your hand inside this product or
touch the ink cartridges during printing.

❏

Do not move the print heads by hand;
otherwise you may damage this product.

❏

Always turn the product off using the

Power

button on the control panel. When this button
is pressed, the

Power

light flashes briefly then

goes off. Do not unplug the power cord or
turn off the product until the

Power

light

stops flashing.

❏

Do not to touch the parts highlighted below.

❏

Do not touch the metal plate located at the
upper left ink cartridge compartment.

«
...
5
6
7
8
9
...
»

Summary of Contents for 11880 - Stylus Pro Color Inkjet Printer























































































































































































Reviews:

No comments

Related manuals for 11880 - Stylus Pro Color Inkjet Printer

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 4

Brand: 3D Systems Pages: 16

Brand: 3D Systems Pages: 28

Brand: 3D Systems Pages: 21

Brand: 3D Systems Pages: 25

Brand: 3D Systems Pages: 23

Brand: 3D Systems Pages: 35

Brand: 3D Systems Pages: 7

Brand: 3D Systems Pages: 13

Brand: 3D Systems Pages: 19

Brand: 3D Systems Pages: 13

Brand: 3D Systems Pages: 2

Brand: 3D Systems Pages: 2

Cubify CUBEX Duo

Brand: 3D Systems Pages: 10

Brand: 3D Systems Pages: 7

Brand: 3DGence Pages: 24

Brand: 3DGence Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands