manualshive.com logo in svg

ePropulsion Pod Drive 1.0 Evo, User Manual, Page: 35 / 48

Share
Download
ePropulsion Pod Drive 1.0 Evo User Manual Download Page 35

33

5.7 Warning Messages

When the pod drive motor is running in abnormal conditions or out of order, a warning 
message with an error code will display on the LCD panel. Figure 5-12 is an example. 

Please find more error codes and corresponding solutions in the below table.

Figure 5-12

Code

Cause

Solution

E01

Battery voltage beyond opera-
tion range. 

Replace a battery based on suggested 

operation specifications.

E02

Propeller may be blocked, 
causing motor overcurrent 

Refer to Solution to E10.

Motor fails or circuit board 
fails causing motor overcur-
rent

Try to turn off the main switch and wait for 
10 seconds then turn on the switch again.

E06

The battery voltage level is 
too low. 

Operate the motor at low power. Please 
charge the battery as soon as possible.

E10

Motor stall, which may be 
caused by blocked propeller 

Turn off power, then clean up the things 
winding around the propeller. Test if the 
propeller can be rotated by hand before 
operation. 

E11

The temperature of motor is 
too high. 

Stop operating the pod drive and wait until 
the temperature falls within the normal 
operating temperature range.

Summary of Contents for Pod Drive 1.0 Evo

















































Reviews:

No comments