epiphan Pearl-2 Rackmount User Manual Download

Page: 93 / 497

Pearl-2 User Guide

Your recordings

5. Tap the

Switch

button to switch the layout that is currently in the

Preview panel

to the

Live panel

The layout that was in the Live panel moves to the Preview panel so that it's ready for the next time
you switch.

6. To load a different layout into the Preview panel, tap another layout in the carousel.

Your recordings

All recordings made using Epiphan Live are saved to the

Your recordings

panel.

Summary of Contents for Pearl-2 Rackmount


















































































































































































































































































































































































































































































































Search results

Summary of Contents for Pearl-2 Rackmount

Reviews:

Related manuals for Pearl-2 Rackmount

Brands by name

Popular brands

epiphan Pearl-2 Rackmount, User Manual

Search results

Summary of Contents for Pearl-2 Rackmount

Reviews:

Related manuals for Pearl-2 Rackmount

Brands by name

Popular brands