epiphan Pearl-2 Rackmount User Manual Download | Manualshive

Page: 64 / 497

background image

Pearl-2 User Guide

Configure the touch screen

3. Uncheck

Allow start/stop recording and streaming

to disable recording, streaming, and live

switching control from the touch screen. Check the check box to enable recording, streaming, and live
switching control.

4. Click

Apply

.

Set the touch screen timeout

Initially, the touch screen is always on for easy monitoring. However, you can set the touch screen to shut off
after a given amount of time. To re-enable the touch screen after it times out and shuts off, simply tap
anywhere on the screen.

To set a timeout for the touch screen:

1. Login to the Admin panel as

admin

, see

Connect to the Admin panel

2. From the Configuration menu, click

Touch Screen

. The touch screen configuration page opens.

51

«
...
62
63
64
65
66
...
»

Summary of Contents for Pearl-2 Rackmount


















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Pearl-2 Rackmount

Brand: Qvis Pages: 112

Brand: TVT Pages: 2

Brand: EyeView Pages: 81

Brand: XVision Pages: 9

Brand: Q-See Pages: 5

Brand: Hitachi Pages: 38

Brand: Idis Pages: 57

Brand: Observint Pages: 109

Brand: Indostar Pages: 63

Brand: Reolink Pages: 55

Brand: Reolink Pages: 65

Brand: GE Interlogix Pages: 88

DS-7204HUHI-K1/E

Brand: HIKVISION Pages: 4

Brand: HIKVISION Pages: 29

Brand: Brovision Pages: 27

Brand: Arris Pages: 128

Brand: Arris Pages: 96

Single Channel DVR

Brand: ACI Farfisa Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands