manualshive.com logo in svg

EOS P 396, Training Manual

Share
Download
EOS P 396 Training Manual Download Page 132

7

Operation of machine & accessories

7.20

Training manual • Basic training • Status 03.14

EOS P 396

➢

Cleaning Unpacking and sieving station.

Preparing plastic powder

The recycled powder must be very carefully mixed with the new powder after sieving. 

If the plastic powder is not mixed carefully or the refresh factor is too low, sink 

marks (surface imperfections) may be seen on the surface of the parts.

Preparing plastic powder using the components of the IPCM P

The recycled powder is added to the recycled powder bin, the new powder to the new 

powder bin on the Powder conveying system P 3. After adjusting the mixture ratio of 

recycled powder to new powder in the dosing station, the refreshed powder is 

transported via the spiral conveyor to the powder supply bin in the machine. You will 

find the mixture ratio recommended by EOS for the plastic powder in the 

application 

instructions

 for the related material.

Necessary activities:

➢

Filling new powder bin and recycled powder bin in the dosing station

➢

Checking levels

➢

Setting mixture ratio on the switching cabinet for the Powder conveying system 

P 3

➢

Switch on Powder conveying system P 3.

You will find further information on unpacking the parts using the Unpacking 

and sieving station in the 

Components IPCM EOSINT P 

manual, section

 9, 

Unpacking and sieving station P 3.

A further EOS accessory for unpacking parts is the Unpacking stand. You will find 

further information on this accessory in the 

Accessories and Option EOS P 396 

manual, section 

6, Unpacking stand.

You will find further information on operation in the 

Components IPCM EOSINT P 

manual, section

 4, Powder conveying system P 3.

Summary of Contents for P 396











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands