EOS P 396 Training Manual Download Page 119

Page: 119 / 170

Operation of machine & accessories

7.7

Training manual • Basic training • Status 03.14

EOS P 396

Making material-specific settings

The materials behave differently during the processing in the machine such that

different powder-specific exposure parameters, recoating parameters and heating

parameters are necessary.
These settings are saved in default jobs that can also be modified.
The exposure and recoating parameters in the default job loaded are loaded

automatically when the

PSW

is started and apply for every new job.

Loading EOS default job

The default parameters for the processing of the materials are saved in the EOS

default jobs. It is important that the default job that matches the material has been

loaded.

☞

Operation EOS P 396

manual, section

6, EOS Loading default job

Preparing user-defined default job

In addition to the EOS default jobs, it is also possible to create user-defined default

jobs.

☞

Operation EOS P 396

manual, section

6, Preparing user-defined default job

Loading user-defined default job

Instead of an EOS default job, a user-defined job can also be loaded.

☞

Operation EOS P 396

manual, section

6, Loading user-defined default job

Summary of Contents for P 396











































































































































































Search results

Summary of Contents for P 396

Reviews:

Brands by name

Popular brands

EOS P 396, Training Manual

Search results

Summary of Contents for P 396

Reviews:

Brands by name

Popular brands