Enviro C-10914 Owner'S Manual Download Page 1

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.

B Y :   S H E R W O O D   I N D U S T R I E S   L T D

OWNER’S MANUAL

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

50-1033

Westport

This appliance may be installed in an after-market 

permanently located, manufactured  (mobile) 

home, where not prohibited by local codes.

This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is 

not convertible for use with other gases, unless a 

certified kit is used.

WHAT TO DO IF YOU SMELL GAS

• Open windows/extinguish any open 

flame.

• Do not try to light any appliance.

• Do not touch any electrical switch or 

use any phone in your building.

• Immediately call your gas supplier from 

a neighbour’s phone.  Follow the gas 

supplier’s instructions.

• If you cannot reach your gas supplier, 

call the fire department.

WARNING

If the information in this manual 

is not followed exactly, a fire or 

explosion may result causing property 

damage, personal injury or loss of 

life. Installation and service must be 

performed by a qualified installer, 

service agency or the gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other 

flammable vapours and liquids in the 

vicinity of this or any other appliance.

Massachusetts  installations  (Warning):  This  product  must  be  installed  by  a  licensed 

plumber  or  gas  fitter  when  installed  within  the  Commonwealth  of  Massachusetts. 

Other Massachusetts code requirements: Flexible connector must not be longer than 

36in, shut-off valve must be a “T” handle gas cock; only direct vent sealed combustion 

products are approved for bedrooms/bathrooms; fireplace dampers must be removed 

or welded in the open position prior to the installation of a fireplace insert or gas log.

Summary of Contents for C-10914















































Reviews: