manualshive.com logo in svg

Enviro 50-1096, Owner'S Manual

Share
Download
Enviro 50-1096 Owner'S Manual Download Page 1

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.

B Y :   S H E R W O O D   I N D U S T R I E S   L T D

OWNER’S MANUAL

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

This appliance is 

only for use with 

the type of gas 

indicated on the 

rating plate. This 

appliance is not 

convertible for use 

with other gases, 

unless a certified 

kit is used.

WHAT TO DO IF YOU SMELL GAS

• Open windows/extinguish any open flame.

• Do not try to light any appliance.

• Do not touch any electrical switch or use any 

phone in your building.

• Immediately call your gas supplier from a 

neighbour’s phone. Follow the gas supplier’s 

instructions.

• If you cannot reach your gas supplier, call the fire 

department.

WARNING

If the information in this manual is not followed exactly, a fire or explosion 

may result causing property damage, personal injury or loss of life. 

Installation and service must be performed by a qualified installer, service 

agency or the gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapours and 

liquids in the vicinity of this or any other appliance.

50-1096

Massachusetts  installations  (Warning):  This  product  must  be  installed  by  a  licensed  plumber  or 

gas fitter when installed within the Commonwealth of Massachusetts. Other Massachusetts code 

requirements: Flexible connector must not be longer than 36in, shut off valve must be a “T” handle 

gas  cock;  only  direct  vent  sealed  combustion  products  are  approved  for  bedrooms/bathrooms; 

fireplace dampers must be removed or welded in the open position prior to the installation of a 

fireplace insert or gas log.

 

Sienna

Summary of Contents for 50-1096
































Reviews:

No comments

Brands by name

Popular brands

Load more brands