ENSIM SENSORS EGW 201 Operating Manual Download Page 1

1

OPERATING

MANUEL

GUIDED RADAR (TDR)  TYPE LEVEL TRANSMITTER

EGW

Model  :

Model : 80-2021-001

Information in this manual is reviewed and completely reliable. Responsibility is not assumed due to any typing error.

Products in this manual are available only for information purpose and they may be changed without notice.

Important Notes:

Used Symbols :

 : Caution

: Note

: Disposal

Please read this manual carefully before installation of the 

Guided Radar (TRD) Type Level Transmitter

. User is responsible

for accidents and losses arising from failure to comply with the warnings in this manual.
In the event that 

Guided Radar (TRD) Type Level Transmitter

 is broken, take measures in order to prevent accidents and l

osses which can occur in its system.
There is not any fuse and circuit breaker on the instrument; they should have been added to the system by the user.
This manual should be stored in an easily accessible place for subsequent use.
The manufacturer's liability cannot exceed the purchase price of the device according to the law.
Do not make any modification on the instrument and do not try to repair it. Reparation should be made by authorized service staff.
Do not operate the system before making assembly in compliance with the assembly chart related to the instrument.
Products which do not contain label and serial number are considered to be excluded from the warranty scope.
The instrument's useful life, determined and announced by the ministry, is 10 years.

Table of Contents :

General Information...........................................................................................................................................................................2
Installation .........................................................................................................................................................................................4
Failure Detection..............................................................................................................................................................................23
Disassembly of Instrument ............................................................................................................................................................23
Service .............................................................................................................................................................................................23
Recalibration....................................................................................................................................................................................23
Repair................................................................................................................................................................................................23
Disposal ...........................................................................................................................................................................................23
Terms of Warranty ..........................................................................................................................................................................23
Terms of Return …………………………………………………………………………………………................................................…23

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.

Models :

EGW 204, EGW 205
EGW 202, EGW 203
EGW 201, EGW 207
EGW 20S

Summary of Contents for EGW 201
























Reviews: