enphase IQ 7 Installation And Operation Manual Download Page 12 | Manualshive

Page: 12 / 43

background image

IQ 7 / IQ 7+ / IQ 7X / IQ 7A with EN4 Bulkhead Installation and Operation

© 2020 Enphase Energy Inc. All rights reserved.

141-00047-01

12

About EN4 Bulkhead Microinverters

If your PV modules have TE PV4S SOLARLOK connectors, or other connectors Listed and identified for
intermatability with the Enphase EN4 bulkhead connector, you may plug them directly into the IQ 7 Series
microinverter with EN4 bulkhead. For other connector combinations, Enphase bulkhead adapters are
required. For models

with the suffix “-E”, the bulkhead connectors are evaluated for use with specific DC

connectors. See the Listed connectors in the following table:

PV Module Connectors Listed and Identified for Intermatability with the Enphase EN4 Bulkhead Connector

Bulkhead

PV module connectors

Enphase part number
830-00533
(EN4 bulkhead)

Manufacturer

Type

(Jinko Solar) Jiangxi Jinko PV Material Co. Ltd.

PV-JK03M-F/2B (female) and
PV-JK03M-M/2B (male)

TE Connectivity (Tyco Electronics)

PV4-SF4.0 (female) and
PV4-SM4.0 (male)

Canadian Solar

T4-PC-1 (female and male)

Enphase Bulkhead Adapters

Adapter

Part

Number

Model SKU

Maximum

Voltage

EN4 (TE PV4-

S SOLARLOK) 150mm/5.9” to MC4*

860-00311

ECA-EN4-S22

80 VDC

EN4 (TE PV4-

S SOLARLOK) to 150mm/5.9” non-

terminated cable.**

860-00312

ECA-EN4-FW

80 VDC

EN4 (TE PV4-S SOLARLOK)

600mm/23.6” to MC4 for

use with split cell modules or PV modules with short DC
cable*

860-00315

ECA-EN4-S22-L

80 VDC

*Qualified per UL subject 9703.
**For field wiring of UL certified DC connectors.

Grounding Considerations

The Enphase Microinverter models listed in this guide do not require grounding electrode conductors
(GEC), equipment grounding conductors (EGC), or grounded conductor (neutral). Your Authority Having
Jurisdiction (AHJ) may require you to bond the mounting bracket to the racking. If so, use UL2703
hardware or star washers. The microinverter itself has a Class II double-insulated rating, which includes
ground fault protection (GFP). To support GFP, use only PV modules equipped with DC cables labeled
PV Wire or PV Cable.

«
...
10
11
12
13
14
...
»

Summary of Contents for IQ 7












































Reviews:

No comments

Related manuals for IQ 7

Brand: NEC Pages: 2

WV7220D - CCTV ACCESSORIES

Brand: Panasonic Pages: 10

WV-NS202 - i-Pro Network Camera

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 4

BB-HGW700A - Network Camera Router

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 19

Brand: Panasonic Pages: 59

Brand: Zacuto Pages: 4

Brand: i-PRO Pages: 2

Brand: cam Pages: 28

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Q-See Pages: 12

Brand: Q-See Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands