manualshive.com logo in svg

enphase Enpower, Installation And Operation Manual

Share
Download
enphase Enpower Installation And Operation Manual Download Page 24

 

Enpower smart switch installation and operation 

 

© 2020 Enphase Energy Inc. All rights reserved. 

141-00046-01 

 

24 

Specifications 

 

MODEL NUMBER 

 

EP200G101-M240US00 

Enphase Enpower smart switch with neutral-forming transformer (NFT), 
Microgrid Interconnect Device (MID), breakers, and screws. Streamlines grid-
independent capabilities of PV and storage installations.   

ACCESSORIES and REPLACEMENT PARTS 

XA-E3-PCBA-ENS 

Replacement Enpower controller printed circuit board 

Circuit breakers (as needed)

A,B

 

BRK-100A-2P-240V  
BRK-125A-2P-240V 
BRK-150A-2P-240V 
BRK-175A-2P-240V 
BRK-200A-2P-240V  
BRK-20A-2P-240V-B  
BRK-30A-2P-240V  
BRK-40A-2P-240V   
BRK-60A-2P-240V  
BRK-80A-2P-240V 

Not included, must be ordered separately:   

• Main Breaker, 2 pole, 100A, 25kAIC, CSR2100 
• Main Breaker, 2 pole, 125A, 25kAIC, CSR2125N 
• Main Breaker, 2 pole, 150A, 25kAIC, CSR2150N 
• Main Breaker, 2 pole, 175A, 25kAIC, CSR2175N 
• Main Breaker, 2 pole, 200A, 25kAIC, CSR2200N 
• Circuit Breaker, 2 pole, 20A, 10kAIC, BR220B 
• Circuit Breaker, 2 pole, 30A, 10kAIC, BR230B 
• Circuit Breaker, 2 pole, 40A, 10kAIC, BR240B 
• Circuit Breaker, 2 pole, 60A, 10kAIC, BR260 
• Circuit Breaker, 2 pole, 80A, 10kAIC, BR280 

EP200G-HNDL-R1 

Enpower installation handle kit (order separately) 

ELECTRICAL SPECIFICATIONS 

 

Assembly rating 

Continuous operation at 100% of its rating 

Nominal voltage / range (L-L) 

240 VAC / 100 - 310 VAC 

Voltage measurement accuracy 

±1% V nominal (±1.2V L-N and ±2.4V L-L) 

Nominal frequency / range 

60 Hz / 56 - 63 Hz 

Frequency measurement accuracy 

±0.1 Hz 

Maximum continuous current rating 

160 A 

Maximum output overcurrent protection 
device 

200 A 

Maximum input overcurrent protection 
device 

200A 

Maximum overcurrent protection device 
rating for storage branch circuit

3

 

80A 

Maximum overcurrent protection device 
rating for PV combiner branch circuit

C

 

80A 

Neutral Forming Transformer (NFT) 

•

 

Breaker rating (pre-installed): 40A between L1 and Neutral; 40A between 
L2 and Neutral 

•

 

Continuous rated power: 3600W 

•

 

Maximum continuous unbalance current: 30A @ 120V 

•

 

Peak rated power: 8800W for 30 seconds 

•

 

Peak unbalanced current: 80A @ 120V for 30 seconds  

Summary of Contents for Enpower


























Reviews:

No comments

Brands by name

Popular brands

Load more brands