manualshive.com logo in svg

enphase Enpower, Installation And Operation Manual

Share
Download
enphase Enpower Installation And Operation Manual Download Page 14

 

Enpower smart switch installation and operation 

 

© 2020 Enphase Energy Inc. All rights reserved. 

141-00046-01 

 

14 

Step 4: Install Breakers as Needed 

The Enpower includes one two-pole 40A circuit breaker that feeds the neutral forming transformer (NFT). 
You can install additional breakers, if needed. You must follow all NEC and local electrical codes.  

Install breakers as needed for the AC grid, main load, Enphase IQ Combiner, Enphase Encharge 
batteries, and generator (reserved for future use¹). These breakers are not included and must be ordered 
separately.  

NOTE

: You must install a backup loads breaker if required by local code. 

NOTE

: Generator connection is not currently supported. This feature will be supported in 

future after an over-the-air software upgrade. 

WARNING

! Risk of injury and equipment damage. Use only the breakers listed in the 

following table.  

Allowed breaker types include:  
 

Enphase Model No. 

Type and Eaton part no. 

BRK-100A-2P-240V  
BRK-125A-2P-240V 
BRK-150A-2P-240V 
BRK-175A-2P-240V 
BRK-200A-2P-240V  
BRK-20A-2P-240V-B  
BRK-30A-2P-240V  
BRK-40A-2P-240V   
BRK-60A-2P-240V  
BRK-80A-2P-240V 

• Main Breaker, 2 pole, 100A, 25kAIC, CSR2100 
• Main Breaker, 2 pole, 125A, 25kAIC, CSR2125N 
• Main Breaker, 2 pole, 150A, 25kAIC, CSR2150N 
• Main Breaker, 2 pole, 175A, 25kAIC, CSR2175N 
• Main Breaker, 2 pole, 200A, 25kAIC, CSR2200N 
• Circuit Breaker, 2 pole, 20A, 10kAIC, BR220B 
• Circuit Breaker, 2 pole, 30A, 10kAIC, BR230B 
• Circuit Breaker, 2 pole, 40A, 10kAIC, BR240B 
• Circuit Breaker, 2 pole, 60A, 10kAIC, BR260 
• Circuit Breaker, 2 pole, 80A, 10kAIC, BR280 

 
 
Breaker installation positions are noted in the diagram: 

A.  Ensure that the Enpower is completely de-energized. 

B.  Open the three latches that lock the enclosure door. 

To release the latch, pull the latch handle forward and 
then to the right. With all the latches opened, swing 
open the enclosure door.  

WARNING

: Risk of equipment damage. Do not 

remove the pre-installed solar shield attached to 
the enclosure door. 

C.  Use a Phillips screw driver to loosen the six screws 

along the periphery of the deadfront. Support the 
deadfront to keep it from falling while performing the 
next step 

Enpower breaker positions 

Summary of Contents for Enpower


























Reviews:

No comments

Brands by name

Popular brands

Load more brands