manualshive.com logo in svg

enphase D380, Troubleshooting Manual

Share
Download
enphase D380 Troubleshooting Manual Download Page 41

Troubleshooting an Enphase System 

 

 2014 Enphase Energy Inc. 

August 2014 

41 

GFI Tripped 

This condition occurs only with the M215, M190, D380, M210, M200, and M175 microinverters. A solid 
red status LED on the microinverter indicates a ground fault (GFDI) error. The LED remains red and the 
Envoy continues to report the fault until the error has cleared.  

If a microinverter registers a GFI Tripped condition, you can attempt to clear this condition through the 
Envoy Interface. An Envoy is required to send the 

clear-gfi message

 to clear the condition. If the 

condition does not clear after you perform the following procedure, contact Enphase Energy customer 
support at 

[email protected]

. 

To send the 

clear-gfi

 message to a microinverter: 

 

1.  From the Administration menu, choose 

Device Conditions and Controls

. 

 

 

 

NOTE

: Do not check the box in the 

Select

 column. 

 

2.  Click on the 

serial number

 of the unit showing the GFI condition. 

The Control Flags screen appears. 

 

CAUTION

: : Do not select the 

reboot

 and 

cmd-alert

 control flags unless recommended by 

Enphase. The functions are:  

 

reboot

 - reboots the inverter 

 

cmd-alert

 - clears a condition flag for a command sent  

Summary of Contents for D380














































Reviews:

No comments

Brands by name

Popular brands

Load more brands