Enovation Controls Murphy EMS PRO LITE Installation And Operation Manual Download Page 46

Page: 46 / 63

Section 40

00-02-0787

2015-03-23

~ 38 ~

M29

DSP Contrast

Lighten the text to a minimum of 8 or darken the
text to a maximum of 35. Factory set to 25.

M30

Heater

The heater is regulated by the Controller that
adjusts the heater depending on the ambient
temperature. Turning this to

could damage the

Controller. Factory set to Heater

OFF

M31

Power ECU

Selecting yes allows ECU data to be shown on
the front display. Selecting YES turns on the ECU
enable output for 3 minutes.

Factory set to YES.

The following are Raw Count displays. Display settings are not changeable.

M32

Inputs 1-4

An X means the input is turned on. I1-8 0000
0000.

M33

Outputs 1-12

An X means the output is turned on. O1-12 0000
0000 0000.

M34

LED 1-2

An X means the LED is turned on. L1-2 00.

M35

Analog in 0

This displays the raw count value of analog 0.
Range 0-1023.

M36

Analog in 1

This displays the raw count value of analog 1.
Range 0-1023.

M37

Analog in 2

This displays the raw count value of analog 2.
Range 0-1023.

M38

Analog in 5

This displays the raw count value of analog 5.
Range 0-1023.

M39

Analog in 6

This displays the raw count value of analog 6.
Range 0-1023.

M40

Analog in 7

This displays the raw count value of analog 7.
Range 0-1023.

M41

Analog in 9

This displays the raw count value of analog 9.
Range 0-1023.

Inputs and Outputs

When wiring to the

EMS PRO LITE

Controller, please refer to the

schematic (included in the box with the controller) illustrating connector
pin outs for the following list of dedicated Inputs & Outputs:

Digital Inputs

Digital Input

Description

Connector

Auto Position of Key Switch

Man Position of Key Switch

Float or Start Contact

Pin G 9 Pos. Conn.

Float or Start Contact

Pin B 9 Pos. Conn.

Summary of Contents for Murphy EMS PRO LITE
































































Search results

Summary of Contents for Murphy EMS PRO LITE

Reviews:

Brands by name

Popular brands

Enovation Controls Murphy EMS PRO LITE, Installation And Operation Manual

Search results

Summary of Contents for Murphy EMS PRO LITE

Reviews:

Brands by name

Popular brands