Introduction
ECB08M230 control box is the main element of the underfloor heating control system. It has
a built-in modules that controls the heat sources (by volt-free relay) and pump (230V AC). The
control box allows to control 8 different zones. It is equipped with 230V AC voltage outputs
actuators. Pluggable terminal blocks provide quick and convenient wiring connections. The
control box is designed to work with NC (normally-closed) type actuators.
Product compliance
Technical Information
Safety information
This product complies with the essential requirements and other relevant provisions of the following
EU Directives: EMC 2014/30/EU, Low Voltage Directive LVD 2014/35/EU, RoHS directive 2011/65/EU.
Use in accordance with national and EU regulations. Device is intended for indoor use only
in dry conditions. Product for indoor use only. Installation must be carried out by a
qualified person in accordance to national and EU regulations.
Before attempting to setup and install, make sure that ECB08M230 is not connected to any
power source. Installation must be carried out by a qualified person. Incorrect installation
may cause damage to the wiring centre. The ECB08M230 should not be installed in areas
where it may be exposed to water or damp conditions.
PLEASE NOTE:
For the entire installation, there may be additional protection requirements, which
the installer is responsible for maintaining.
Power Supply
230 V AC 50 Hz
Total Load Max
6 (3) A
Pump Load Max
3A
Boiler Load Max
6A
Actuator Load Max
2A
Thermostat Load Max
1A
Outputs
Pump control (230V AC)
Boiler control (NO/COM/NC)
Terminals for actuators (230V AC)
Dimensions [mm]
327 x 110 x 37
Control Box description
1.
Cartridge fuse 5 x 20 mm T6,3A
2.
Power supply (AC 230V)
3.
Pump control output (AC 230V)
7.
LED diodes indicators for the operation status of the pump,
boiler and control box power supply connection
8.
LEDs 1 to 8 informing about the operation of zones 1-8
4. Boiler control output (volt free)
The boiler control output is supported by a relay with voltage-free contacts
(NO / COM / NC output). The boiler must be connected to the COM-NO
or COM-NC contacts. It is a typical two-state relay. In most cases, the NC terminal is
not used. If the thermostats connected to the wiring centre send a signal for heating,
the BOILER output contacts activate the relay with a 3-minute delay, allowing the
boiler to be turned on. The boiler is turned off immediately, when none of the zones
sends a signal for heating.
2. Power supply
Power supply for wiring centre is 230 V ~ 50Hz.
Installation features:
• three-wire,
• made in accordance with applicable regulations.
The red LED indicates that the wiring centre is connected to the power supply.
1. Fuse
Please note:
Replacement of the fuse to be carried out only when the
control box is disconnected from power supply (230 V ~).
Main fuse is located under the housing cover next to power supply terminals and
secures the control box and the devices connected to it. Use ceramic tube slow blow
250 V ROHS fuses (5x20 mm) with nominal max current 6,3A. To replace fuse remove
the fuse holder with a flat screwdriver and pull out the fuse.
4.
Boiler control output (volt free)
5.
Thermostats input connections
6.
Actuators output connections (AC 230V)
Quick Guide
Ver. 1
Release date: I 2022
ECB08M230
| Wiring centre
www.engocontrols.com
The PUMP OUTPUT is used to power the circulation pump in the heating system.
It is a 230V AC voltage output with a maximum load capacity of 3A. The pump is
connected directly to the contacts. The output is turned on (the pump starts) always
after 3 minutes from the moment of receiving a heating signal from any thermostat
connected to the wiring centre. The output is turned off (the pump stops) as soon as
the last thermostat stops reporting heat demand.
3. Pump control output (AC 230V)
When the Pump/Valve control output is
activated, the pump status LED shows a
constant
green
light.
When the BOILER control output is
activated, the boiler status LED shows a
constant
green
light.
PLEASE NOTE:
Before starting the installation, disconnect the 230V power
supply!
NO
COM
NC
BOILER OUTPUT
Boiler ON/OFF contacts
(according to the boiler’s manual)
BOILER
Distributor:
QL CONTROLS Sp z o.o. Sp. k.
43-262 Kobielice
4 Rolna St.
Poland
OUTPUT_1
N
N
SL1
SL1
OUTPUT_2
N
N
SL2
SL2
OUTPUT_3
N
N
SL3
SL3
OUTPUT_4
N
N
SL4
SL4
OUTPUT_5
N
N
SL5
SL5
OUTPUT_6
N
N
SL6
SL6
OUTPUT_7
N
N
SL7
SL7
OUTPUT_8
N
N
SL8
SL8
N
N
L
L
PUMP OUTPUT
WIRING CENTRE
ECB08M230
POWER SUPPLY
AC 230V
VOLT FREE
AC 230V
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
FUSE 6.3A
N
N
L
L
INPUT_1
N
SL1
L
INPUT_2
N
SL2
L
INPUT_3
N
SL3
L
INPUT_4
N
SL4
L
INPUT_5
N
SL5
L
INPUT_6
N
SL6
L
INPUT_7
N
SL7
L
INPUT_8
N
SL8
L
BOILER OUTPUT
NO
NC
COM
PE
PE
LED
LED
LED
2
6
5
8
3
4
1
LED
LED
LED
Pump status Boiler status Power supply
7
OUTPUT_1
N
N
SL1
SL1
OUTPUT_2
N
N
SL2
SL2
OUTPUT_3
N
N
SL3
SL3
OUTPUT_4
N
N
SL4
SL4
OUTPUT_5
N
N
SL5
SL5
OUTPUT_6
N
N
SL6
SL6
OUTPUT_7
N
N
SL7
SL7
OUTPUT_8
N
N
SL8
SL8
N
N
L
L
PUMP OUTPUT
LISTWA STERUJĄCA
ECB08M230
POWER SUPPLY
AC 230V
VOLT FREE
AC 230V
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
FUSE 6.3A
N
N
L
L
INPUT_1
N
SL1
L
INPUT_2
N
SL2
L
INPUT_3
N
SL3
L
INPUT_4
N
SL4
L
INPUT_5
N
SL5
L
INPUT_6
N
SL6
L
INPUT_7
N
SL7
L
INPUT_8
N
SL8
L
BOILER OUTPUT
NO
NC
COM
PE
PE
LED
LED
LED
230 V AC
L
N
OUTPUT_1
N
N
SL1
SL1
OUTPUT_2
N
N
SL2
SL2
OUTPUT_3
N
N
SL3
SL3
OUTPUT_4
N
N
SL4
SL4
OUTPUT_5
N
N
SL5
SL5
OUTPUT_6
N
N
SL6
SL6
OUTPUT_7
N
N
SL7
SL7
OUTPUT_8
N
N
SL8
SL8
N
N
L
L
PUMP OUTPUT
LISTWA STERUJĄCA
ECB08M230
POWER SUPPLY
AC 230V
VOLT FREE
AC 230V
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
FUSE 6.3A
N
N
L
L
INPUT_1
N
SL1
L
INPUT_2
N
SL2
L
INPUT_3
N
SL3
L
INPUT_4
N
SL4
L
INPUT_5
N
SL5
L
INPUT_6
N
SL6
L
INPUT_7
N
SL7
L
INPUT_8
N
SL8
L
BOILER OUTPUT
NO
NC
COM
PE
PE
LED
LED
LED
L
N
3 A
max
OUTPUT_1
N
N
SL1
SL1
OUTPUT_2
N
N
SL2
SL2
OUTPUT_3
N
N
SL3
SL3
OUTPUT_4
N
N
SL4
SL4
OUTPUT_5
N
N
SL5
SL5
OUTPUT_6
N
N
SL6
SL6
OUTPUT_7
N
N
SL7
SL7
OUTPUT_8
N
N
SL8
SL8
N
N
L
L
PUMP OUTPUT
LISTWA STERUJĄCA
ECB08M230
POWER SUPPLY
AC 230V
VOLT FREE
AC 230V
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
ACTUAROR
THERMOSTAT
LED
FUSE 6.3A
N
N
L
L
INPUT_1
N
SL1
L
INPUT_2
N
SL2
L
INPUT_3
N
SL3
L
INPUT_4
N
SL4
L
INPUT_5
N
SL5
L
INPUT_6
N
SL6
L
INPUT_7
N
SL7
L
INPUT_8
N
SL8
L
BOILER OUTPUT
NO
NC
COM
PE
PE
LED
LED
LED