‐
01
‐
‐
02
‐
‐
03
‐
ZWN-RSM1
Smart Single Relay Switch Module
SPECIFICATIONS
Voltage...........................................................................120-277VAC, 50/60Hz
Maximum Load requirement......................................................................10A
Z-Wave Frequency.................................................................. 908.42MHz(US)
Operating Temperature.................................................................32° F-104° F
Size.....................................................................................1.77'' ×1.65'' ×0.72''
Range......................................................................Up to 132 feet line of sight
between the Wireless Controller and the closest Z-Wave receiver module.
FEATURES
z
Work with existing light switches, required neutral wire
z
Slim size module with build in Z-Wave technology and Interoperable
with other Z-Wave enabled devices
z
On/Off control via Z-Wave controller, manual wall switch
z
Acts as a Z-Wave repeater to extend the range
z
3 way wiring compatible
DESCRIPTION
Z-Wave unifies all your home electronics into an integrated wireless
network and helps them talk to each other. It can be added to the network,
and making your home electronics fully compatible. The ZWN-RSM1 Switch
Module is a component of lighting control system, it can’t be used separately
but should turn an existing switch into a Z-Wave switch. This ZWN-RSM1
module is a Z-Wave enabled device and fully interoperable with other Z-Wave
certified device from other manufacturers and/or other applications. In a
Z-Wave network, each device is designed to act as a wireless repeater. Once
the ZWN-RSM1 module is installed and setup with in your wall, it will
retransmit the RF signal from one device to another until the intended device
is reached. This ensures that the signal is received by its intended destination
by routing the signal around obstacles and radio dead spots.
WARNINGS AND CAUTIONS
INSTALLATION
Simple Wiring Diagram:
Fig1
3-way Circuits
Wiring Diagram:
Fig2
IMPORTANT NOTE ABOUT 3-WAY CIRCUITS
The term “3-way circuit” refers to a circuit with two switches and one load (light)
like you find at the top and bottom of a stairway. There are many ways to
physically wire a 3-way circuit and it is important to understand how the circuit
you wish to upgrade to Z-Wave control is wired. One of the ways , the Aux of
ZWN-RSM1 to wire a 3way switch 2(Fig2), then wire to 3way switch 1 ,and
then wire to the line. Although very common and by no means a standard, it is
the easiest to convert to Z-Wave control. With this type of circuit, ZWN-RSM1
is set behind the switch 2. Do not change the wiring of switch 1. Please note
that both switch 1 and switch 2 must be 3-way switch.
Please consult an electrician if you have trouble identifying the type of wiring circuit
you wish to convert or if you do not feel confident in your ability to convert the
circuit to Z-Wave control.
To be installed and/or used in accordance with appropriate electrical codes and
regulations. Exercise extreme caution when using Z-Wave devices to control
appliances. Operation of the Z-Wave device may be in a different room than the
controlled appliance, also an unintentional activation may occur if the wrong button
on the remote is pressed. Z-Wave devices may automatically be powered on due
to timed event programming. Depending upon the appliance, these unattended or
unintentional operation could possibly result in a hazardous condition. Z-Wave
enabled devices should never be used to supply power to, or control the On/Off
status of medical and/or life support equipment. If you are unsure or uncomfortable
about performing the installation, please consult a qualified electrician.
PLUS
1. WARNING : To avoid fire, shock, or death. Turn off power at circuit breaker or
fuse and test that power is off before wiring.
2. Remove wall plate and switch mounting screws.
3. Carefully remove the switch from the switch box.
4. Disconnect the wiring from the existing switch.
5. Connect the ZWN-RSM1 module as shown in the wiring diagram
6. Check connections to be sure they are tight and no bare conductors are
exposed
7. Insert the ZWN-RSM1 module into the box first, then wire the existing switch.
8. Attach the wall plate.
9. Restore power at the circuit breaker and test the system.
TIPS FOR ARRANGING THE ANTENNA:
z
Locate the antenna as far from metal elements as possible to prevent interferences.
z
Metal surfaces in the direct vicinity of the antenna may impair signal reception.
z
Do not cut or shorten the antenna , its length is perfectly matched.
OPERATIONS
Manual Control
1. Manually turn ON the ZWN-RSM1 Module: Flick1 times of the
AUX
switch
The load of the module will turn ON.
2. Manually turn OFF the ZWN-RSM1 Module: Flick1 times of the
AUX
switch
The load of the Module will turn OFF.
3. When the controller is in add mode, and once program button is pressed
and release, or Flick 3 times of the connected switch in 1.5S will also set
the ZWN-RSM1 module enter into learn mode . and then the controller will
verify the add.
4. When the controller is in remove mode, and once program button is
pressed and release, or Flick 3 times of the connected switch in 1.5S will
also set the ZWN-RSM1 module enter into learn mode . and then the
controller will verify the remove.
5. Once program button is pressed and hold for 10 second, the device will
send a device reset locally notification to controller. Then clear all of
information for the network, and restore factory defaults, and reset the
module. Use this procedure only in the event that the network primary
controller is missing or otherwise inoperable.
