Endress 333363 Translation Of The Original Operating Manual Download

Page: 57 / 78

The device in-use

DANGER!

Fire and explosion hazard from leaking fuel

Risk of severe to deadly burns.
► Prevent fuel from leaking.
► Keep the refuelling device’s fuel cannister firmly closed.
► When changing the fuel cannister, stay as far away as possible from the pow-

er generator.

► Remove unneeded fuel cannisters from the power generator’s work area im-

mediately.

► Smoking, naked flames and sparks are forbidden.

Fig. 8-7 Refuelling device connection

Connect refuelling
device

1. Remove the stoppers from the hose holes on the base frame.

2. Make sure the 2-way tap’s lever is in internal tank position (“INSIDE”).

3. Remove the dummy plugs from the feed and return connections.

4. Guide the ready-made fuel hoses for the refuelling device though the holes

and screw them as follows to the connections on the 3-way tap:
a) Connect the fuel feed hose.
b) Connect the fuel return hose.

5. Put the lever for the 2-way tap in “OUTSIDE” position.

6. Start the generator (see Chapter 7.3 ) and wait for the RPM to stabilize.

The refuelling device is attached. The power generator is supplied with fuel
through the refuelling device.

Summary of Contents for 333363















































































Search results

Summary of Contents for 333363

Reviews:

Related manuals for 333363

Brands by name

Popular brands

Endress 333363, Translation Of The Original Operating Manual

Search results

Summary of Contents for 333363

Reviews:

Related manuals for 333363

Brands by name

Popular brands