Endress+Hauser Waterpilot FMX21 Operating Instructions Manual Download Page 126

Page: 126 / 144

Accessories

Waterpilot FMX21

126

Hauser

Accessories

• Observe the additional information in the individual sections!

• For additional information, see the sections "Mechanical construction" (in the

Technical Information), "Environment", →  137, "Process" →  139 and

"Mounting" →  17.

Suspension clamp

For easy installation of the device, Hauser offers a suspension clamp.

• Product Configurator: the suspension clamp is optionally available

• Order number: 52006151

A0030950

Terminal box

Terminal box for terminal strip, temperature head transmitter and Pt100.

• Product Configurator: the terminal box is optionally available

• Order number: 52006152

A0030967

4-terminal strip/terminals

4-terminal strip for wiring

Order number: 52008938

A0030951

Temperature head transmitter TMT71 for FMX21 4 to 20 mA analog

PC-programmable (PCP) temperature head transmitter for the conversion of various input

signals.

• Product Configurator: the temperature head transmitter TMT71 is optionally available

→  126

• Order number: 52008794

A0030952

Summary of Contents for Waterpilot FMX21

















































































































































Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands

Endress+Hauser Waterpilot FMX21, Operating Instructions Manual

Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands