Endress+Hauser Waterpilot FMX21 Operating Instructions Manual Download Page 124

Page: 124 / 144

Description of device parameters

Waterpilot FMX21

124

Hauser

14.20 Expert → Diagnosis → Simulation

Simulation mode

Write permission

Operators/Service engineers/Expert

Description

Switch on simulation and select the simulation mode. When changing the measuring

mode or the "Lin. mode" level type or when the device is restarted, any simulation that may

be running is switched off.

Options

• None

• Pressure →see this table, "Sim. pressure" parameter

• Level, → see this table, "Sim. level" parameter

• Tank content, → see this table, "Sim. tank cont." parameter

• Current, → see this table, "Sim. current" parameter

• Alarm/warning, → see this table, "Sim. error no."

Factory setting

None

Transducer block

→

Pressure

→

↑

↓

Sensor

→

Sensor trim → Position adjustment

→

Damping

→

Level

→

→ Current output

↑

Simulation value
Pressure

• Simulation value level
• Simulation value tank content

Sim.
current

Sim. pressure

Write permission

Operators/Service engineers/Expert

Description

Enter the simulation value. See also "Simulation mode".

Prerequisite

"Simulation mode" = Pressure

Value at switch-on

Current pressure measured value

Sim. level

Write permission

Operators/Service engineers/Expert

Description

Enter the simulation value. See also "Simulation mode".

Summary of Contents for Waterpilot FMX21

















































































































































Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands

Endress+Hauser Waterpilot FMX21, Operating Instructions Manual

Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands