Endress+Hauser Waterpilot FMX21 Operating Instructions Manual Download Page 43

Page: 43 / 144

Waterpilot FMX21

Commissioning

Hauser

Navigation

Setup → Measuring mode

Write permission

Operator/Maintenance/Expert

Description

Select the measuring mode.

The operating menu is structured differently depending on the measuring mode selected.

Options

• Pressure

• Level

Factory setting

Level

9.5

Selecting the pressure engineering unit

Press. eng. unit

Navigation

Setup → Press. eng. unit

Write permission

Operator/Maintenance/Expert

Description

Select the pressure unit. If a new pressure unit is selected, all pressure-specific parameters

are converted and displayed with the new unit.

Options

• mbar, bar

• mmH2O, mH2O, inH2O

• ftH2O

• Pa, kPa, MPa

• psi

• mmHg, inHg

• kgf/cm

Factory setting

mbar or bar depending on the nominal measuring range of the sensor module, or as per

order specifications.

9.6

Position adjustment

A pressure shift resulting from the orientation of the device can be corrected by the

position adjustment.

Pos. zero adjust (gauge pressure sensor)

Navigation

Setup → Pos. zero adjust

Write permission

Operator/Maintenance/Expert

Description

Pos. zero adjustment – the pressure difference between zero (set point) and the measured

pressure need not be known.

Summary of Contents for Waterpilot FMX21

















































































































































Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands

Endress+Hauser Waterpilot FMX21, Operating Instructions Manual

Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands