Endress+Hauser Waterpilot FMX21 Operating Instructions Manual Download Page 38

Page: 38 / 144

Operation options

Waterpilot FMX21

Hauser

The "Operator code" parameter is used to lock/unlock the device.

Operator code

Navigation

Setup → Extended setup → Operator code

Read permission

Operator/Maintenance/Expert

Write permission

Operator/Maintenance/Expert

Description

Use this function to enter a code to lock or unlock operation.

User entry

• To lock: Enter a number

the release code (value range: 1 to 65535).

• To unlock: Enter the release code.

Factory setting

Note

The release code is "0" in the order configuration. Another release code can be defined in

the "Code definition" parameter. If the user has forgotten the release code, the release code

can be made visible by entering the number "5864".

The release code is defined in the "Code definition" parameter.

Code definition

Navigation

Setup → Extended setup → Code definition

Read permission

Operator/Maintenance/Expert

Write permission

Operator/Maintenance/Expert

Description

Use this function to enter a release code with which the device can be unlocked.

User entry

A number from 0 to 9999

Factory setting

Note

The device setup can also be disabled on the RIA15 via a 4-digit user code.

Additional information is available in the RIA15 Operating Instructions BA01170K.

Summary of Contents for Waterpilot FMX21

















































































































































Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands

Endress+Hauser Waterpilot FMX21, Operating Instructions Manual

Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands