Endress+Hauser Waterpilot FMX21 Operating Instructions Manual Download Page 28

Page: 28 / 144

Electrical connection

Waterpilot FMX21

Hauser

6.1.4

Device, RIA15 with installed HART communication resistor

module

The HART communication module for installation in the RIA15 (for Ex or non-Ex

areas) can be ordered together with the device.
The

voltage drop

to be taken into account is max.

7 V

Compensation of the atmospheric pressure must be ensured for the installation. A

black, vented cable gland is supplied for this purpose.

Without backlighting

LED

A0020839

 4

Block diagram; device connection, RIA15 without light, HART communication resistor

HART communication resistor module

Device

Power supply

With backlighting

LED

A0020840

 5

Block diagram; device connection, RIA15 with light, HART communication resistor module

HART communication resistor module

Device

Power supply

6.1.5

Wire colors

RD = red, BK = black, WH = white, YE = yellow, BU = blue, BR = brown

6.1.6

Connection data

Connection classification as per IEC 61010-1:

• Overvoltage category 1

• Pollution level 1

Connection data in the hazardous area

See relevant XA.

Summary of Contents for Waterpilot FMX21

















































































































































Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands

Endress+Hauser Waterpilot FMX21, Operating Instructions Manual

Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands