Endress+Hauser Waterpilot FMX21 Operating Instructions Manual Download Page 23

Page: 23 / 144

Waterpilot FMX21

Mounting

Hauser

5.9

Inserting the cable into the RIA15 field housing

TX20

A0017830

Inserting the cable, field housing, connection without transmitter power supply (example)

1. Release the housing screws
2. Open the housing
3. Open the cable gland (M16) and insert the cable
4. Connect the cable including the functional grounding and close the cable gland

Compensation of the atmospheric pressure must be ensured for the installation. A

black, vented cable gland is supplied for this purpose.
If using the communication resistance module in the RIA15, the cable of the device

must be inserted into the right gland when connecting the device so that the

integrated pressure compensation tube is not pinched.

5.10 Cable marking

A0030955

Summary of Contents for Waterpilot FMX21

















































































































































Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands

Endress+Hauser Waterpilot FMX21, Operating Instructions Manual

Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands