Endress+Hauser Waterpilot FMX21 Operating Instructions Manual Download Page 134

Page: 134 / 144

Technical data

Waterpilot FMX21

134

Hauser

16.2.4 Protocol-specific data

• Manufacturer ID: 17 (11 hex)

• Device type ID: 25 (19 hex)

• Device revision: 01 (01 hex) - SW version 01.00.zz

• HART specification: 6

• DD revision: 01

• Device description files (DTM, DD):

•

www.endress.com

•

www.fieldcommgroup.org

• HART load: min. 250 Ω

• HART device variables. The dynamic variables SV, TV and QV may be assigned to any

device variable:

• Standard process values for SV, TV (second and third device variable) are dependent

on the measuring mode: pressure, level

• Standard process value for QV (fourth device variable) is the sensor temperature:

temperature

• Measured values for PV (first device variable) are dependent on the measuring mode:

pressure, level, tank content

• Supported functions:

• Burst mode

• Additional transmitter status

• Device locking

• Alternative measuring modes

• Catch variable

• Long tag

Summary of Contents for Waterpilot FMX21

















































































































































Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands

Endress+Hauser Waterpilot FMX21, Operating Instructions Manual

Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands