Endress+Hauser Waterpilot FMX21 Operating Instructions Manual Download Page 110

Page: 110 / 144

Description of device parameters

Waterpilot FMX21

110

Hauser

14.12 Expert→ Communication → HART config.

Burst mode

Write permission

Service engineers/Expert

Description

Switching burst mode on and off.

Options

• On

• Off

Factory setting

Off

Burst option

Write permission

Service engineers/Expert

Description

You can use this parameter to define which command is sent to the master.

Options

• 1 (HART command 1)

• 2 (HART command 2)

• 3 (HART command 3)

• 9 (HART command 9)

• 33 (HART command 33)

Factory setting

1 (HART command 1)

Current mode

Write permission

Service engineers/Expert

Description

Configure current mode for HART communication.

Options

• Signaling

Measured value transmission by the current value

• Fixed

Fixed current 4.0 mA (Multidrop mode)

(Measured value transmission via HART digital communication only)

Factory setting

Signaling

Bus address

Summary of Contents for Waterpilot FMX21

















































































































































Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands

Endress+Hauser Waterpilot FMX21, Operating Instructions Manual

Search results

Summary of Contents for Waterpilot FMX21

Reviews:

Related manuals for Waterpilot FMX21

Brands by name

Popular brands