manualshive.com logo in svg

Endress+Hauser Soliwave FDR16, Operating Instructions Manual

Share
Download
Endress+Hauser Soliwave FDR16 Operating Instructions Manual Download Page 39

Soliwave FDR16/FQR16

Hauser

39

Technical data

13�4�3  Degree of protection

• 

.

: IP69

• 

-

: IP67

13�4�4  Vibration resistance

• Vibration according to EN 60068-2-6

• 

Excitation: Sine

• 

Frequency range: 5 to 500 Hz

• 

Amplitude: 5 to 15 Hz (5.5 mm) peak / 15 to 500 Hz 5 g

• 

Passing speed: 1 octave per minute

• 

Test directions: 3 directions (X, Y, Z)

• 

Test duration: approx. 140 minutes per direction (approx. 70 minutes per temperature/

direction)

• 

Test temperature: -40 to +70 °C

13.4.5 

Shock resistance

• Shock according to EN 60068-2-27

• 

Excitation: half sine

• 

Shock duration: 18 ms

• 

Amplitude: 30 g

• 

Number of shocks: 3 per direction and temperature

• 

Test directions: 6 directions (±X, ±Y, ±Z)

• 

Test temperature: -40 to +70 °C

13�4�6  Electromagnetic compatibility

• Interference emission to EN 61326, Electrical Equipment Class B

• Interference immunity to EN 61326, Appendix A (Industrial)

13.5 

Process

13.5.1 

Process temperature

• 

-20 to +60 °C (-4 to +140 °F)

• 

-20 to +450 °C (-4 to +842 °F) with optional high temperature adapter

• 

Observe deviating temperature ranges for the accessories offered!

13.5.2 

Process pressure

• 0.5 to 6.8 bar (7 to 99 psi) absolute, only to be observed for direct process mounting

• 0.8 to 5.1 bar (12 to 74 psi) absolute, when using the optional high temperature adap-

ter

• 0.5 to 21 bar (7 to 305 psi) absolute, when using the optional high pressure adapter

• 

Observe deviating pressure ranges for the accessories offered!

13�6 

Additional technical data

  

Latest technical information: Hauser website:

 

www.endress.com

 → Downloads.

Summary of Contents for Soliwave FDR16









































Reviews:

No comments

Brands by name

Popular brands

Load more brands