Endress+Hauser Proline Promag 55 Operating Manual Download Page 84 | Manualshive

Page: 84 / 130

background image

3 Transducer Block

Device functions Proline Promag 55 FOUNDATION Fieldbus

84

Hauser

Process - Pressure
Shock Suppression

AUTO - OOS

The closure of a valve can cause brief but severe movements of the fluid in
the piping system, movements which the measuring system registers. The
pulses totaled in this way result in a totalizer reading error, particularly in
the case of batching processes. For this reason, the measuring device is
equipped with pressure shock suppression (= short-term signal
suppression) which can eliminate system-related "disruptions".

!

Note!

Note that pressure shock suppression cannot be used unless the low flow
cut off is active (see the "Low Flow Cut Off - On Value" parameter

Use this function to define the time span for active pressure shock
suppression.

Activation of pressure shock suppression

Pressure shock suppression is activated once the flow falls below the
switch-on point of the low flow cut off (see point

a

in graphic).

While pressure shock suppression is active, the following conditions apply:
• Flow reading on display

→

0

• Totalizer reading

→

The totalizers are pegged at the last correct value.

Deactivation of pressure shock suppression

The pressure shock suppression is deactivated after the time interval, set
in this function, has passed (see point

b

in graphic).

!

Note!

The actual flow value is displayed and output, when the time interval for
the pressure shock suppression has passed and the flow exceeds the
switch-off point of the low flow cut off (see point

c

in graphic).

A0001285-EN

m

= on value (low flow cut off),

n

= off value (low flow cut off)

User input:

Max. 4-digit number, incl. unit: 0.00 to 100.0 s

Factory setting:

0.00 s

"Flow" Transducer Block/base index 1400

Parameter

Write access with

operating mode

(MODE_BLK)

Description

n

m

a

b

c

inactive

active

inactive

t

Pressure shock suppression

Command:
Valve closes

Q

Given time

After filling

«
...
82
83
84
85
86
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: Calira Pages: 14

Brand: Panasonic Pages: 116

Toughbook CF-T7BWATAAM

Brand: Panasonic Pages: 12

Brand: Campbell Pages: 70

Brand: Yuasa Pages: 35

Brand: 3M Pages: 10

Brand: Dacor Pages: 4

Brand: RAKINDA Pages: 20

Brand: ZALMAN Pages: 20

Brand: Yakima Pages: 11

Brand: Vega Pages: 2

Brand: Vega Pages: 11

Brand: ABLE Pages: 20

Brand: Harol Pages: 16

Brand: Pivot Pages: 4

Brand: Oki Pages: 2

Brand: hepco & becker Pages: 6

Brand: Badabulle Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands