Endress+Hauser Proline Promag 55 Operating Manual Download Page 6 | Manualshive

Page: 6 / 130

background image

2 Function matrix

Device Functions Proline Promag 55 FOUNDATION Fieldbus

6

Hauser

2

Function matrix

2.1

General layout of the function matrix

The function matrix consists of four levels:

Blocks -> Groups -> Function groups -> Functions

A0000961

2.1.1

Blocks (A, B, C, etc.)

The blocks are the highest-level grouping of the operation options for the device.
The blocks include, for example: MEASURED VARIABLES, QUICK SETUP, USER INTERFACE,
TOTALIZER, etc.

2.1.2

Groups (AAA, AEA, CAA, etc.)

A block consists of one or more groups. Each group represents a more detailed selection of the
operation options in the higher-order block. The groups in the
USER INTERFACE block, for example, include: CONTROL, MAIN LINE, ADDITIONAL LINE, etc.

2.1.3

Function groups (000, 020, 060, etc.)

A group consists of one or more function groups. Each function group represents a more detailed
selection of the operation options in the higher-order group. The function groups available in the
CONTROL group are for example: BASIC CONFIGURATION, UNLOCKING/LOCKING,
OPERATION, etc.

2.1.4

Functions (0000, 0001, 0002, etc.)

Each function group consists of one or more functions. The functions are used to operate and
parameterize the device. Numerical values can be entered here or parameters selected and saved.
The functions in the BASIC CONFIGURATION function group include LANGUAGE, DISPLAY
DAMPING, CONTRAST LCD, etc. The procedure for changing the language of the user interface,
for example, is as follows:

1.

Select the USER INTERFACE block

2.

Select the CONTROL group

3.

Select the BASIC CONFIGURATION function group

4.

Select the LANGUAGE function (here you can set the language required).

…

…

…

…

…

…

…

…

0001

2001

0401

2021

2201

0002

2002

0402

2022

2202

0003

2003

0403

2023

2203

0009

2009

0409

2029

2209

0429

2049

2069

0421

2041

0422

2042

0423

2043

2063

2061

2062

0000

2000

0400

2020

2200

0420

2040

2060

000

200

040

202

220

042

204

206

AAA

BAA

ACA

CAA

CBA

D, E, …

A

B

C

«
...
4
5
6
7
8
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: ULTIMATE SPEED Pages: 19

Brand: Galeo Pages: 19

Brand: Hama Pages: 40

Brand: Rave Sports Pages: 16

Brand: Wagan Pages: 12

7400DN - Phaser Color LED Printer

Brand: Xerox Pages: 3

ShowMatch DeltaQ SMGSB

Brand: Bose Pages: 2

Brand: Oki Pages: 2

Brand: Alpine Pages: 8

Brand: Adam Pages: 22

Brand: BS Bodensteckdosen Systemtechnik Pages: 14

Brand: hepco & becker Pages: 6

Brand: Thule Pages: 8

Brand: Jaypro Sports Pages: 2

Brand: Fisher-Price Pages: 12

01 29 9 416 497

Brand: BMW Pages: 5

Yepp Nexxt Mini 12080101

Brand: Thule Pages: 8

Brand: York Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands