Endress+Hauser Proline Promag 55 Operating Manual Download Page 49 | Manualshive

Page: 49 / 130

background image

Device Functions Proline Promag 55 FOUNDATION Fieldbus

7 Block BASIC FUNCTION

Hauser

49

7.3

Group SYSTEM PARAMETER

7.3.1

Function group CONFIGURATION

BASIC FUNCTION

G

⇒

FOUNDATION FIELDBUS GGA

⇓

PROCESS PARAMETER

GIA

⇓

SYSTEM PARAMETER

GLA

⇒

CONFIGURATION

660

Function description

BASIC FUNCTION

→

SYSTEM PARAMETER

→

CONFIGURATION

INSTALLATION
DIRECTION
SENSOR
(6600)

Use this function to reverse the sign of the flow measured variable, if necessary.

Options:

NORMAL (flow as indicated by the arrow)
INVERSE (flow opposite to direction indicated by the arrow)

Factory setting:

NORMAL

!

Note!

Ascertain the actual direction of fluid flow with reference to the direction indicated by
the arrow on the sensor (nameplate).

SYSTEM DAMPING
(6603)

Use this function to set the filter depth of the digital filter. This reduces the sensitivity of
the measuring signal to interference peaks (e.g. high solids content, gas bubbles in the
fluid, etc.). The reaction time of the measuring system increases with every increase in
the filter setting.

User input:

0 to 15

Factory setting:

7

!

Note!

The system damping acts on all functions and outputs of the measuring device.

INTEGRATION TIME
(6604)

Use this function to view the set integration time.

The integration time defines the duration of internal totaling of the induced voltage in the
fluid (measured by the measuring electrode), i.e. the time in which the measuring device
records the true flow (afterwards the magnetic field for the next integration is created
from the opposite pole).

User interface:

Max. 2-digit number: 1 to 65 ms

Factory setting:

5 ms

POSITIVE ZERO RETURN
(6605)

Use this function to interrupt evaluation of measured variables. This is necessary when a
piping system is being cleaned, for example. This setting acts on all function and outputs
of the measuring device.

Options:

OFF
ON

→

Signal output is set to the "ZERO FLOW" value.

Factory setting:

OFF

«
...
47
48
49
50
51
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Two-Knife Booklet Trimmer-A1

Brand: Canon Pages: 32

Perfect Binder-C1

Brand: Oce Pages: 82

Brand: Canon Pages: 16

Brand: Canon Pages: 48

Brand: Hamax Pages: 74

Brand: Napoleon Pages: 2

Brand: Zipp Pages: 39

DWSC - Vintage C

Brand: Daikin Pages: 57

Brand: Eaton Pages: 2

Brand: Rally Pack Pages: 2

Brand: rako Pages: 3

Brand: Zagg Pages: 2

Canon C100 Z-Finder

Brand: Zacuto Pages: 14

Brand: Panasonic Pages: 242

Brand: Farad Pages: 8

Brand: Acuity Brands Pages: 3

AAB-P-RZR900-K2-001

Brand: SuperATV Pages: 3

Brand: Omega Engineering Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands