Endress+Hauser Proline Promag 55 Operating Manual Download Page 43

Page: 43 / 130

Device Functions Proline Promag 55 FOUNDATION Fieldbus

7 Block BASIC FUNCTION

Hauser

7.1.3

Function group INFORMATION

BASIC FUNCTION

⇒

FOUNDATION FIELDBUS GGA

⇒

CONFIGURATION

620

⇓

FUNCTION BLOCKS

6122

⇓

INFORMATION

624

Function description

BASIC FUNCTION

→

FOUNDATION FIELDBUS

→

INFORMATION

MANUFACTURER ID
(6240)

Use this function to view the manufacturer ID in decimal numerical format.

User interface:

452B48 (hex) for Hauser

DEVICE TYPE
(6241)

Use this function to view the device ID in hexadecimal numerical format.

User interface:

1042 (hex) for Promag 55 FOUNDATION Fieldbus

SERIAL NUMBER
(6242)

Use this function to view the serial number.

User interface:

11-digit number

DEVICE REVISION
(6243)

Use this function to view the device revision number.

Note!

The information displayed here can be used to ensure that the correct system files
(DD = Device Description) are used for integration into the host system. The system files
can be downloaded free of charge from the Internet at www.endress.com.

Example:
Information displayed in the DEVICE REVISION function (6243)

→

Information displayed in the DD REVISION function (6244)

→

required device description files (DD)

→

0301.sym / 0301.ffo

DD REVISION
(6244)

Use this function to view the revision number of the device description.

Note!

Example:
Information displayed in the DEVICE REVISION function (6243)

→

Information displayed in the DD REVISION function (6244)

→

required device description files (DD)

→

0301.sym / 0301.ffo

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands