Endress+Hauser Proline Promag 55 Operating Manual Download Page 36

Page: 36 / 130

6 Block TOTALIZER

Device Functions Proline Promag 55 FOUNDATION Fieldbus

Hauser

6.1

Group TOTALIZER (1 to 3)

6.1.1

Function group CONFIGURATION

TOTALIZER

⇒

TOTALIZER 1

DAA

⇒

CONFIGURATION

300

⇓

TOTALIZER 2

DAB

⇒

CONFIGURATION

300

⇓

TOTALIZER 3

DAC

⇒

CONFIGURATION

300

Function description

TOTALIZER

→

TOTALIZER (1 to 3)

→

CONFIGURATION

The function descriptions below apply to Totalizers 1 to 3; the totalizers are independently configurable.

ASSIGN
(3000)

Use this function to assign a measured variable to the totalizer in question.

Options:

OFF
MASS FLOW
VOLUME FLOW

Factory setting:

VOLUME FLOW

Note!

• The totalizer is reset to "0" as soon as the selection is changed.
• If you select OFF, the function group CONFIGURATION (300) of the totalizer in

question only displays the ASSIGN (3000) function.

UNIT TOTALIZER
(3001)

Use this function to define the unit for the totalizer's measured variable, as selected
beforehand.

Options: (for MASS FLOW assignment):

Metric

→

g; kg; t

→

oz; lb; ton

Factory setting:

Nominal diameter and country dependent

→

Page 123 ff.

Options (for VOLUME FLOW assignment):

Metric

→

; dm

; m

; ml; l; hl; Ml Mega

→

cc; af; ft

; oz f; gal; Kgal; Mgal; bbl (normal fluids); bbl (beer);

bbl (petrochemicals); bbl (filling tanks)

Imperial

→

gal; Mgal; bbl (beer); bbl (petrochemicals)

Factory setting:

Nominal diameter and country dependent

→

Page 123 ff.

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands