Endress+Hauser Proline Promag 55 Operating Manual Download Page 33 | Manualshive

Page: 33 / 130

background image

Device Functions Proline Promag 55 FOUNDATION Fieldbus

5 Block USER INTERFACE

Hauser

33

5.4.2

Function group MULTIPLEX

USER INTERFACE

C

⇒

CONTROL

CAA

⇓

MAIN LINE

CCA

⇓

ADDITIONAL LINE

CEA

⇓

INFORMATION LINE

CGA

⇒

CONFIGURATION

260

⇓

MULTIPLEX

262

Function description

USER INTERFACE

→

INFORMATION LINE

→

MULTIPLEX

ASSIGN
(2620)

Use this function to define the second reading to be displayed in the information line
alternately (every 10 seconds) with the value defined in the function ASSIGN (2600).

Options:

OFF
VOLUME FLOW IN %
MASS FLOW IN %
VOLUME FLOW BARGRAPH IN %
MASS FLOW BARGRAPH IN %
FLOW VELOCITY
OPERATING/SYSTEM CONDITIONS
FLOW DIRECTION READING
AI1 - OUT VALUE
AI2 - OUT VALUE
AI3 - OUT VALUE
AI4 - OUT VALUE
AI5 - OUT VALUE
PID - IN VALUE (controlled variable)
PID - CAS IN VALUE (external set point)
PID - OUT VALUE (manipulated variable)
DEVICE PD-TAG (tag name)

Factory setting:

OFF

!

Note!

Multiplex mode is suspended as soon as a fault / notice message is generated. The
message in question appears on the display. Once the fault is eliminated, the measuring
device resumes operation in Multiplex mode and the error message is no longer displayed
on the local display.

100%-VALUE
(2621)

!

Note!

This function is not available unless one of the following was selected in the ASSIGN
function (2620):
• VOLUME FLOW IN %
• MASS FLOW IN %
• VOLUME FLOW BARGRAPH IN %
• MASS FLOW BARGRAPH IN %

Use this function to define the flow value to be shown on the display as the 100% value.

User input:

5-digit floating-point number

Factory setting:

Nominal diameter and country dependent

«
...
31
32
33
34
35
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: Makita Pages: 20

Brand: IBS Pages: 24

Brand: Panasonic Pages: 1

Brand: Kabuto Pages: 25

MES ACURAS HEAD

Brand: Barco Pages: 131

PORTABLE AIR CONDITIONER & COOLER

Brand: Icebreeze Pages: 12

AERASGARD RCO2-W

Brand: S+S Regeltechnik Pages: 32

Brand: Panasonic Pages: 2

Brand: Taffio Pages: 8

Brand: HBM Pages: 40

Brand: FujiFilm Pages: 13

Brand: Scame electrical solutions Pages: 8

Sleeptrainer Palm the penguin

Brand: NENKO Pages: 4

Brand: Solight Pages: 2

651665 00 22-00-40

Brand: hepco & becker Pages: 5

Brand: Thule Pages: 4

Brand: Sable Pages: 15

Brand: Quantum Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands