Endress+Hauser Proline Promag 55 Operating Manual Download Page 21

Page: 21 / 130

Device Functions Proline Promag 55 FOUNDATION Fieldbus

5 Block USER INTERFACE

Hauser

CONTRAST LCD
(2003)

Use this function to optimize display contrast to suit local operating conditions.

User input:

10 to 100%

Factory setting:

50%

BACKLIGHT
(2004)

Use this function to optimize the backlight to suit local operating conditions.

User input:

0 to 100%

Note!

Entering the value "0" means that the backlight is "switched off". The display then no
longer emits any light, i.e. the display texts can no longer be read in the dark.

Factory setting:

50%

Function description

USER INTERFACE

→

CONTROL

→

BASIC CONFIGURATION

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands