Endress+Hauser Proline Promag 55 Operating Manual Download Page 119 | Manualshive

Page: 119 / 130

background image

Device functions Proline Promag 55 FOUNDATION Fieldbus

6 Discrete Output Function block

Hauser

119

6

Discrete Output Function block

The Discrete Output function block (DO, Discrete Output) processes a discrete setpoint value
received from an upstream function block or higher level process control system, with which
various instrument functions (e.g. zero point adjustment or totalizer reset) can be initiated in the
downstream Transducer Block.

6.1

Signal processing

The figure shows the internal structure of the Discrete Output function blocks Promag 55
FOUNDATION Fieldbus:

A0004771-en

Fig. 5:

Signal processing in the Discrete Output function block

In the CAS operating mode (cascade operation), the Discrete Output function block receives, via the
function block input CAS_IN_D, a discrete signal from an upstream function block. This signal
controls the setpoint value (parameter SP_D) of the function block, and after internal calculation is
sent as an output signal (parameter OUT_D) to the Transducer Block for control of instrument
functions (e.g. zero point adjustment). The output value and status of the Discrete Output function
block is communicated to the upstream block via the output BKCAL_OUT_D.

Signal processing in the RCAS operating mode (remote cascade operation) is largely identical to the
CAS operating mode. However, in this operating mode, control of the parameter SP_D does not take
place via an upstream function block but through a process control system. The output value and
status of the Discrete Output function block is communicated to the process control system as an
answer message via parameter RCAS_OUT_D.

A0003816-en

CAS_IN _D

= Remote setpoint value from another function block

OUT_D

= Discrete output value and status

BKCAL_OUT_D

= Discrete output value and status required by BKCAL_IN_D input of another block for

OUT_D

BKCAL_OUT_D

CAS_IN_D

DO

RCAS_IN_D

IO_OPTS

SIMULATE_D

SIMULATE_D

Discrete

Input

Transducer Blocks

Discrete

Output

MODE_BLK

CAS_IN_D

PV_D

BKCAL_OUT_D

OUT_D

(Mode Man)

(Mode Auto)

SP_D

Discrete Output Function Block

Invert.

RCAS_OUT_D

(Mode CAS)

(Mode RCAS)

«
...
117
118
119
120
121
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: Banner Pages: 12

Brand: Valore Pages: 5

BMP 01-ZLZPP 1A 00-P S75 Series

Brand: Balluff Pages: 20

Brand: Öhlins Pages: 8

Brand: Öhlins Pages: 9

Brand: Larson Electronics Pages: 2

Brand: Stobag Pages: 3

PowerPack TPB-2112

Brand: texet Pages: 16

ALK.00.733.15000/B

Brand: SW-Motech Pages: 14

MOBILE COOLING TROPICOOL TC07

Brand: Dometic Pages: 156

Brand: Fuzion Pages: 8

USB temperature

Brand: MADRIX Pages: 2

Brand: A&D Pages: 4

Canon PowerShot A700

Brand: Ikelite Pages: 6

ClickShare CSC-1

Brand: Barco Pages: 3

Brand: Gordon AirPlay Pages: 7

Brand: Thule Pages: 12

Brand: Walimex Pro Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands