Endress+Hauser Proline Promag 55 Operating Manual Download Page 109 | Manualshive

Page: 109 / 130

background image

Device functions Proline Promag 55 FOUNDATION Fieldbus

3 Transducer Block

Hauser

109

Tot. 1 to 3 - Sum

AUTO - OOS

Use this parameter to view the total for the totalizer’s measured variable
aggregated since measuring commenced. The value can be positive or
negative, depending on the setting selected in the parameter
"Tot. 1 to 3 - Mode" (

Page 110), and the direction of flow.

!

Note!

• The effect of the setting in the parameter "Tot. 1 to 3 - Mode" is as

follows:
– If the setting is "BALANCE", the totalizer balances flow in the positive

and negative directions.

– If the setting is "FORWARD", the totalizer registers only flow in the

positive direction.

– If the setting is "REVERSE", the totalizer registers only flow in the

negative direction.

• The totalizer's response to faults is defined in the parameter

"Tot. - Failsafe All".

Tot. 1 to 3 - Unit

AUTO - OOS

Use this parameter to define the unit for the totalizer's measured variable,
as selected beforehand.

Options: (for MASS FLOW assignment):

Metric

→

g; kg; t

US

→

oz; lb; ton

Factory setting:

Nominal diameter and country dependent

Options (for VOLUME FLOW assignment):

Metric

→

cm

3

; dm

3

; m

3

; ml; l; hl; Ml Mega

US

→

cc; af; ft

3

; oz f; gal; Kgal; Mgal; bbl (normal fluids); bbl (beer);

bbl (petrochemicals); bbl (filling tanks)

Imperial

→

gal; Mgal; bbl (beer); bbl (petrochemicals)

Factory setting:

Nominal diameter and country dependent

!

Note!

The unit selected here does not have any effect on the desired volume unit
which should be transmitted by means of the FOUNDATION Fieldbus
interface. This setting is made separately by means of the corresponding AI
Block in the XD_SCALE parameter group.

Tot. 1 to 3 - Assign

AUTO - OOS

Use this parameter to assign a measured variable to the totalizer.

Options:

OFF
MASS FLOW
VOLUME FLOW

Factory setting:

VOLUME FLOW

!

Note!

The totalizer is reset to "0" as soon as the selection is changed.

"Totalizer" Transducer Block/base index 1900:

Parameter

Write access with

operating mode

(MODE_BLK)

Description

«
...
107
108
109
110
111
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

MMAC-Plus 9F116-01

Brand: Cabletron Systems Pages: 4

Brand: Caberg Pages: 16

Brand: Vello Pages: 12

Brand: Hama Pages: 6

Brand: Hama Pages: 2

Brand: ICON ProAudio Pages: 29

Brand: Kargo Master Pages: 5

Brand: Tait Pages: 10

Powersaver Dual Flexi

Brand: Sangamo Pages: 2

Brand: Xantrex Pages: 3

Brand: Imax Pages: 3

2 SD Card Memory Module NI 9802

Brand: National Instruments Pages: 16

Single Sensor Set

Brand: Revbox Pages: 10

Brand: Viking Pages: 10

RELATIVE HUMIDITY SENSOR BT72i

Brand: CMA Dishmachines Pages: 4

Brand: OnStar Pages: 22

Brand: iArmor Pages: 4

Brand: FuzzDog Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands