Endress+Hauser Proline Promag 55 Operating Manual Download Page 105 | Manualshive

Page: 105 / 130

background image

Device functions Proline Promag 55 FOUNDATION Fieldbus

3 Transducer Block

Hauser

105

Info Line -
Display Mode

AUTO - OOS

!

Note!

The option is not active unless one of the following was selected in the
parameter "Info Line - Assign" (

• MASS FLOW BARGRAPH IN %
• VOLUME FLOW BARGRAPH IN %

Use this parameter to define the format of the bar graph.

Options:

STANDARD (Simple bar graph with 25 / 50 / 75% gradations and
integrated sign).

A0001258

SYMMETRY (Symmetrical bar graph for positive and negative directions of
flow, with –50 / 0 / +50% gradations and integrated sign).

A0001259

Factory setting:

STANDARD

Info Line Mux -
Assign

AUTO - OOS

Use this parameter to define the second reading to be displayed in the info
line alternately (every 10 seconds) with the value defined in the parameter
"Info Line - Assign" (

Options:

OFF
VOLUME FLOW IN %
MASS FLOW IN %
VOLUME FLOW BARGRAPH IN %
MASS FLOW BARGRAPH IN %
FLOW VELOCITY
OPERATING/SYSTEM CONDITIONS
DISPLAY FLOW DIRECTION
TOTALIZER (1 to 3)
AI1 - OUT VALUE
AI2 - OUT VALUE
AI3 - OUT VALUE
AI4 - OUT VALUE
AI5 - OUT VALUE
PID - IN VALUE (controlled variable)
PID - CAS IN VALUE (external set point)
PID - OUT VALUE (manipulated variable)
DEVICE PD-TAG (tag name)

Factory setting:

OFF

!

Note!

Multiplex mode is suspended as soon as a fault / notice message is
generated. The message in question appears on the display. Once the fault
is eliminated, the measuring device resumes operation in Multiplex mode
and the error message is no longer displayed on the local display.

"Display" Transducer Block/base index 1800:

Parameter

Write access with

operating mode

(MODE_BLK)

Description

«
...
103
104
105
106
107
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: Paradyne Pages: 86

Brand: Ranger design Pages: 6

Brand: Hahnel Pages: 176

Brand: Panasonic Pages: 18

Brand: Jabra Pages: 2

Brand: Fenix Pages: 4

Brand: Aroflora Pages: 36

Brand: Exact solutions Pages: 40

Brand: GENUS Pages: 10

Brand: Enviro Pages: 4

Brand: EGO Pages: 2

Transit Vancouver Wagon

Brand: Webasto Pages: 44

Brand: BAFANG Pages: 6

AVID DISC BRAKES

Brand: Avid Technology Pages: 2

GemLightbox Aerial

Brand: Picup Media Pages: 13

Brand: Manfrotto Pages: 14

DRI3030TEN-CONTF-BLK

Brand: Superior Fireplaces Pages: 2

Brand: HBM Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands