manualshive.com logo in svg

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Share
Download
Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 96

Description of device parameters

Proline Promag 300 Modbus RS485

96

Hauser

Cal. factor

Navigation

 Expert → Sensor → Calibration → Cal. factor (6522)

Description

Displays the current calibration factor for the sensor.

User interface

Positive floating-point number

Factory setting

Depends on nominal diameter and calibration.

Zero point

Navigation

 Expert → Sensor → Calibration → Zero point (6546)

Description

This function shows the zero point correction value for the sensor.

User interface

Signed floating-point number

Factory setting

Depends on nominal diameter and calibration

Cond. cal. fact.

Navigation

 Expert → Sensor → Calibration → Cond. cal. fact. (6718)

Prerequisite

The 

On

 option is selected in the 

Conduct. measur.

 parameter (→   74) parameter.

Description

Displays the calibration factor for the conductivity measurement.

User interface

0.01 to 10

 

000

3.3  

"I/O configuration" submenu

Navigation

 Expert → I/O config.

‣

I/O config.

I/O 1 to n terminals (3902–1 to n)

→   97

I/O 1 to n info (3906–1 to n)

→   97

I/O 1 to n type (3901–1 to n)

→   98

Summary of Contents for Proline Promag 300

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands