manualshive.com logo in svg

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Share
Download
Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 89

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

89

Install. direct.

Navigation

 Expert → Sensor → Sensor adjustm. → Install. direct. (1809)

Description

Use this function to change the sign of the medium flow direction.

Selection

• In arrow direct.

• Against arrow

Factory setting

In arrow direct.

Additional information

Description

Before changing the sign: ascertain the actual direction of fluid flow with reference to

the direction indicated by the arrow on the sensor nameplate.

Integration time

Navigation

 Expert → Sensor → Sensor adjustm. → Integration time (6533)

Description

Display the duration of an integration cycle.

User interface

1 to 65 ms

Measuring period

Navigation

 Expert → Sensor → Sensor adjustm. → Measuring period (6536)

Description

Display the time of a full measuring period.

User interface

0 to 1

 

000 ms

"Variable adjust" submenu

Navigation

 Expert → Sensor → Sensor adjustm. → Variable adjust

‣

Variable adjust

Vol. flow offset (1831)

→   90

Vol. flow factor (1832)

→   90

Mass flow offset (1841)

→   91

Summary of Contents for Proline Promag 300

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands