manualshive.com logo in svg

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Share
Download
Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 71

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

71

Cond. temp.coeff (1891)

→   75

Temp. damping (1886)

→   74

Ref.density (1885)

→   75

‣

Low flow cut off

→   76

‣

Empty pipe det.

→   79

‣

ECC

→   81

Filter options

Navigation

 Expert → Sensor → Process param. → Filter options (6710)

Description

Use this function to select a filter option.

Selection

• Adaptive

• Adaptive CIP on

• Dynamic

• Dynamic CIP on

• Binomial

• Binomial CIP on

Factory setting

Binomial

Additional information

Description

The user can choose from a range of filter combinations which can optimize the

measurement result depending on the application. Each change in the filter setting affects

Summary of Contents for Proline Promag 300

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands