manualshive.com logo in svg

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Share
Download
Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 168

Description of device parameters

Proline Promag 300 Modbus RS485

168

Hauser

Unit totalizer 1 to n

Navigation

 Expert → Application → Totalizer 1 to n → Unit totalizer 1 to n (0915–1 to n)

Prerequisite

One of the following options is selected in the 

Assign variable

 parameter (→   167) of

the 

Totalizer 1 to n

 submenu:

• Volume flow

• Mass flow

• Correct.vol.flow

Description

Use this function to select the process variable unit for the Totalizer 1 to n (→   167).

Selection

SI units

• g

• kg

• t

US units

• oz

• lb

• STon

or

SI units

• cm³

• dm³

• m³

• ml

• l

• hl

• Ml Mega

US units

• af

• ft³

• fl oz (us)

• gal (us)

• kgal (us)

• Mgal (us)

• bbl (us;liq.)

• bbl (us;beer)

• bbl (us;oil)

• bbl (us;tank)

Imperial units

• gal (imp)

• Mgal (imp)

• bbl (imp;beer)

• bbl (imp;oil)

or

SI units

• Nl

• Nm³

• Sm³

US units

• Sft³

• Sgal (us)

• Sbbl (us;liq.)

Imperial units

Sgal (imp)

or

Other units

None

Factory setting

l

Additional information

Description

The unit is selected separately for each totalizer. It is independent of the selection

made in the 

System units

 submenu (→   55).

Selection

The selection is dependent on the process variable selected in the 

Assign variable

parameter (→   167).

Summary of Contents for Proline Promag 300

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands