manualshive.com logo in svg

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Share
Download
Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 162

Description of device parameters

Proline Promag 300 Modbus RS485

162

Hauser

Sec. identific.

Navigation

 Expert → Communication → WLAN settings → Sec. identific. (2718)

Description

Use this function to select the security settings (download via the menu: Data

Management > Security > Download WLAN).

User interface

• Root certificate

• Device certific.

• Dev. private key

User name

Navigation

 Expert → Communication → WLAN settings → User name (2715)

Description

Use this function to enter the user name.

User entry

–

Factory setting

–

WLAN password

Navigation

 Expert → Communication → WLAN settings → WLAN password (2716)

Description

Use this function to enter the WLAN password.

User entry

–

Factory setting

–

WLAN IP address

Navigation

 Expert → Communication → WLAN settings → WLAN IP address (2711)

Description

Use this function to enter the IP address of the measuring device's WLAN connection.

User entry

4 octet: 0 to 255 (in the particular octet)

Factory setting

192.168.1.212

Summary of Contents for Proline Promag 300

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands