Endress+Hauser Oxymax COS22 Series Operating Instructions Manual Download Page 25

Page: 25 / 36

Accessories

Hauser

Accessories

8.1

Connection accessories

Special measuring cable COK21
• Cable length 3 m (9.8 ft)

order no. 51505870

• Cable length 10 m (33 ft)

order no. 51505868

8.2

Installation accessories

Flowfit CPA240
• pH/redox flow assembly for processes with a high level of requirements
• Technical Information TI179C/07/en

Cleanfit CPA475
• Retractable assembly for installation in tanks and pipework under sterile conditions
• Technical Information TI240C/07/en

Unifit CPA442
• Installation assembly for food, biotechnology and pharmaceuticals, with EHEDG and 3A certificate
• Technical Information TI306C/07/en

Cleanfit CPA450
• Manual retractable assembly for installing 120 mm sensors in tanks and pipework
• Technical Information TI183C/07/en

Flow assembly for 120 mm sensors
• compact stainless steel assembly with low sample volume
• order no.: 71042404

Summary of Contents for Oxymax COS22 Series





































Search results

Summary of Contents for Oxymax COS22 Series

Reviews:

Related manuals for Oxymax COS22 Series

Brands by name

Popular brands

Endress+Hauser Oxymax COS22 Series, Operating Instructions Manual

Search results

Summary of Contents for Oxymax COS22 Series

Reviews:

Related manuals for Oxymax COS22 Series

Brands by name

Popular brands